R60/2021-A-NL1-25.15 Rev. 0
OIML Certificate
OIML Member State The Netherlands
Number R60/2021-A-NL1-25.15 revision 0
Project number 3996892
Page 1 of 2
Issuing authority
NMi Certin B.V.
Person responsible: M.Ph.D. Schmidt
Applicant and Manufacturer
SARL ASSOCIATION DE CONTROLES TECHNIQUES
265 avenue des Ebénistes
ZA bel air - BP 3343
12000 RODEZ
France
Identification of the certified type
A compression load cell, with strain gauges. Registered trade name ACT
Type
: CPB, CPBF
Characteristics
See next page
This OIML Certificate is issued under scheme A.
This Certificate attests the conformity of the above identified Type (represented by the sample(s) identified in the OIML Test Report) with the requirements of the following Recommendation of the International Organization of Legal Metrology (OIML):
OIML R 60-1:2021 for accuracy class C
This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation above-identified. This Certificate does not bestow any form of legal international approval.
Important note: Apart from the mention of the Certificate's reference number and the name of the OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of the associated OIML Test Report(s) is not permitted, although either may be reproduced in full.
Issuing Authority
NMi Certin B.V., OIML Issuing Authority NL1 21 November 2025
Certification Board
This document is issued under the provision that no liability is accepted and that the applicant shall indemnify third-party liability.
This document is digitally signed and sealed. The digital signature can be verified in the blue ribbon on top of the electronic version of this certificate.
OIML Certificate
OIML Member State The Netherlands
Number R60/2021-A-NL1-25.15 revision 0 Project number 3996892 Page 2 of 2
The conformity was established by the results of tests and examinations provided in the associated report:
No. NMi-2224556-01 revision 1 dated 16 December 2019 that includes 28 pages.
Characteristics of the load cell:
| Characterization of load cell capabilities | Analog-passive load cell |
| Maximum capacity ($E_{\mathrm{max}}$) | 15t up to and including 75t |
| Minimum dead load | 0kg |
| Accuracy Class | C |
| Rated Output | 2,0mV/V |
| Maximum number of load cell intervals(n)^{(1)}$ | 4000 |
| Ratio of minimum LC Verification interval^{(1)}$ $Y=E_{\mathrm{max}}/v_{\mathrm{min}}$ | 10000 |
| Ratio of minimum dead load output return^{(1)}$ $Z=E_{\mathrm{max}}/(2*\mathrm{DR})$ | 12000 |
| Input impedance | 800$\Omega\pm5\Omega$ |
| Temperature range | -10℃/+40℃ |
| Fraction $p_{\mathrm{LC}}$ | 0,7 |
| Humidity Class | CH |
| Safe overload | 150% of $E_{\mathrm{max}}$ |
| Output impedance | 705$\Omega\pm5\Omega$ |
| Recommended excitation | 10V AC/DC |
| Excitation maximum | 15V AC/DC |
| Transducer material | Stainless steel |
| Atmospheric protection | Hermetically welded |
Remark:
- The characteristics for $ n_{\mathrm{max}} $ , Y and Z can be reduced separately.
Each load cell produced is provided with an accompanying document with information about its characteristics.
Revision History
| Revision | Date | Change(s) |
| 0 | 2025-11-21 | Initial issue. |