R60/2021-A-NL1-24.16 Rev. 0
OIML Certificate
OIML Member State The Netherlands
Number R60/2021-A-NL1-24.16 revision 0 Project number 3811488 Page 1 of 3
Issuing authority
Applicant and Manufacturer
NMi Certin B.V.
Person responsible: M.Ph.D. Schmidt
WIKA Alexander Wiegand SE & Co. KG Alexander-Wiegand-Str. 30 63911 Klingenberg Germany
Identification of the certified type
A bending beam load cell, with strain gauges Registered trade name WIKA
Type
Characteristics
See next page
This OIML Certificate is issued under scheme A.
This Certificate attests the conformity of the above identified Type (represented by the sample(s) identified in the OIML Test Report) with the requirements of the following Recommendation of the International Organization of Legal Metrology (OIML):
OIML R 60-1:2021 for accuracy class C
This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation above-identified. This Certificate does not bestow any form of legal international approval.
Important note: Apart from the mention of the Certificate's reference number and the name of the OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of the associated OIML Test Report(s) is not permitted, although either may be reproduced in full.
Issuing Authority
NMi Certin B.V., OIML Issuing Authority NL1 3 May 2024
Certification Board
This document is issued under the provision that no liability is accepted and that the applicant shall indemnify third-party liability.
OIML Certificate
OIML Member State The Netherlands
Number R60/2021-A-NL1-24.16 revision 0 Project number 3811488 Page 2 of 3
The conformity was established by the results of tests and examinations provided in the associated reports:
No. NMi-2309247-01 dated 4 September 2019 that includes 52 pages;
No. NMi-2309247-02 dated 4 September 2019 that includes 24 pages;
No. NMi-2309247-03 dated 4 September 2019 that includes 24 pages.
Characteristics of the load cell:
| Characterization of load cell capabilities | Analog passive load cell | ||
| Maximum capacity ($E_{\mathrm{max}}$) | 5kg up to 30kg | 30kg up to 100kg | 100kg up to and including 500kg |
| Minimum dead load | 0kg | ||
| Accuracy Class | C | ||
| Rated Output | 2mV/V±0.1mV/V | ||
| Maximum number of load cell intervals(n)^{(1)}$ | 4000 | 3000 | 4000 |
| Ratio of minimum LC Verification interval(1) $Y=E_{\mathrm{max}}/v_{\mathrm{min}}$ | 20000 | ||
| Ratio of minimum dead load output return(1) $Z=E_{\mathrm{max}}/(2*\mathrm{DR})$ | 4000 | ||
| Input impedance | 400$\Omega\pm20\Omega$ | ||
| Temperature range | -10℃/+40℃ | ||
| Fraction $p_{\mathrm{LC}}$ | 0.7 | ||
| Humidity Class | CH | ||
| Safe overload | 200% of $E_{\mathrm{max}}$ | ||
| Output impedance | 350$\Omega\pm3\Omega$ | ||
| Recommended excitation | 10VAC/DC | ||
| Excitation maximum | 15VAC/DC | ||
| Transducer material | Stainless steel | ||
| Atmospheric protection | Hermetically sealed/welded | ||
Remark:
- The characteristics for $ n_{\mathrm{max}} $ , Y and Z can be reduced separately.
Each load cell produced is provided with an accompanying document with information about its characteristics.
OIML Certificate
OIML Member State The Netherlands
Number R60/2021-A-NL1-24.16 revision 0 Project number 3811488
Page 3 of 3
The above identified Type (represented by the sample(s) identified in the OIML Test Report) have been found to comply with the additional national requirements established by the United States of America (NIST Handbook 44 and NCWM Publication 14), included in the Utilizer Declaration:
R 60 OIML-CS rev.2 Additional requirements from the United States Accuracy class III L;
R 60 OIML-CS rev.2 Additional requirements from the United States Marking requirements.
Revision History
| Revision | Date | Change(s) |
| 0 | 2024-05-03 | Initial issue. |