R139/2018-A-NL1-23.02 Rev. 0

OIML Member State The Netherlands

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 1 of 6

Issuing authority NMi Certin B.V. Person responsible: M.Ph.D. Schmidt

Applicant and Manufacturer CZAR Metric System Private Limited Plot No. A-451 MIDC Industrial Area, Mahape Navi Mumbai 400710 Maharashtra, India

Identification of the CNG Dispenser

certified type

Manufacturers mark: Czar

Type: CZC-******[1]

Characteristics See following pages

This OIML Certificate is issued under scheme A.

This Certificate attests the conformity of the above identified type (represented by the sample(s) identified in the OIML Type Evaluation Report) with the requirements of the following Recommendation of the International Organization of Legal Metrology (OIML):

R 139:2018 "Compressed gaseous fuel measuring systems for vehicles"

Accuracy class 1,5

This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation identified above. This Certificate does not bestow any form of legal international approval.

This certificate and supporting reports comply with the requirements of OIML-CS-PD-07 clause 6.2.

Important note: Apart from the mention of the Certificate's reference number and the name of the OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of the associated OIML Type Evaluation Report(s) is not permitted, although either may be reproduced in full.

[1] Where " $ \star $ " can be a number or a letter for representing different configurations of the dispenser.

Issuing Authority

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 2 of 6

The conformity was established by the results of tests and examinations provided in the associated report:

• No. NMi-2502536-04 dated 4 May 2023 that includes 27 pages.

Characteristics of the CNG Dispenser

CNG Dispenser CZC-******* series

In Table 1 the general characteristics of the CNG dispenser are presented.

The construction of the CNG dispenser is recorded in the Documentation folder no. CF2502536-1.

Each CZC-******* dispenser consists at least of:

• One measurement transducer (Coriolis mass meter CNGmass (E+H) or Coriolis mass meter CNG 050 (Emerson)).

• One electronic calculating/indicating device (CZ series calculator).

• Optionally, a printer may be connected to the dispenser as follows:

• Printer mounted on the dispenser door, powered and communication through the dispenser;

• Printer mounted on the side of the dispenser, powered and communication through the dispenser;

Remote printer connected via the POS communication cable.

The calculating/indicating device can have a maximum of 4 main displays, allowing it to configure and control 4 nozzles (meters), out of which 4 nozzles (meters) can be simultaneously operated.

OIML Member State The Netherlands

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 3 of 6

A maximum of one nozzle (meter) can be connected to each calculating/indicating device's main display.

Approved input - Mass meter communication cable via RS-485

Approved output - POS communication cable via RS-485

All communication cables (POS and Mass meter communication) should be shielded cables.

The characteristics of the mentioned parts of the dispenser are presented at table 2 and higher.

Essential parts of the CZC-***** series CNG dispensers

The conformity of the following parts was established by the results of tests and examinations provided in the associated reports:

Part:

Calculating/indicating device

Producer:

CZAR Metric System Private Limited

Type:

CZ Series

Documentation folder:

DF2502536-2

No. NMi-2502536-01 dated 27 October 2021 that includes 119 pages;

Reports:

No. NMi-2502536-03 dated 4 May 2023 that includes 34 pages.

OIML Member State The Netherlands

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 4 of 6

Software version verification of the calculating/indicating device type CZ series The software versions and checksums can be displayed on the LCD display by following the below procedure:

On the alphanumeric keypad on the dispenser press SETUP $ \rightarrow $ P2 $ \rightarrow $ enter unique password by a user with sufficient rights $ \rightarrow $ ENTER this puts the dispenser in maintenance mode.

Then press 5 $ \rightarrow $ 1 $ \rightarrow $ 1 $ \rightarrow $ 1 for CPU board

or 5 $ \rightarrow $ 1 $ \rightarrow $ 1 $ \rightarrow $ 2 for Main Display board.

OIML Member State The Netherlands

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 5 of 6

Part:

Producer:

Type:

Measurement transducer

Endress+Hauser Flowtec AG.

Documentation folder:

Reports:

CNGmass

TC10997-1

No. CPC-607296-1a dated 7 February 2007;

No. CPC-10200012-02a dated 8 February 2010;

No. NMi-16200831-01 dated 13 July 2017;

No. NMi-16200831-02 dated 19 July 2017;

No. NMi-2665464-01 dated 5 April 2022.

OIML Member State The Netherlands

Number R139/2018-A-NL1-23.02 revision 0 Project number 2502536 Page 6 of 6

Part:

Producer:

Measurement transducer

Type:

Emerson Process Management Flow B.V.

CNG 050

Documentation folder:

TC11012-1

Reports:

No. CPC/9200574-2 dated 26 January 2010.

No. NMi-1900487-01 dated 14 July 2017.

Production location

The CNG dispenser is produced at one of the following production locations:

• CZAR Metric System Private Limited, Plot No. A-451, Central Road, MIDC Industrial Area,

• Mahape Pin code 400710, Maharashtra India.

• CZAR Metric System Private Limited, Plot No.C-541, MIDC Industrial Area, Pawne,

Navi Mumbai 400705, Maharashtra, India.

Certificate history:

This revision replaces the previous version.