R129/2020-A-NL1-24.03 Rev. 1
OIML Certificate
OIML Member State The Netherlands
Number R129/2020-A-NL1-24.03 revision 1
Project number 3984005
Page 1 of 3
Issuing authority
NMi Certin B.V.
Person responsible: M.Ph.D. Schmidt
Applicant and Manufacturer
Metrilus GmbH
Gräfenberger Str. 32
91050 Uttenreuth
Germany
Identification of the certified type
A Multi-Dimensional Measuring instrument
Type : MetriXFreight L135
MetriXFreight L235
MetriXFreight L335
MetriXFreight L635
Characteristics
See next page
This OIML Certificate is issued under scheme A.
This Certificate attests the conformity of the above identified Type (represented by the sample(s) identified in the OIML Test Report) with the requirements of the following Recommendation of the International Organization of Legal Metrology (OIML):
OIML R 129-1:2020
This Certificate relates only to the metrological and technical characteristics of the type of measuring instrument covered by the relevant OIML International Recommendation above-identified. This Certificate does not bestow any form of legal international approval.
Important note: Apart from the mention of the Certificate's reference number and the name of the OIML Member State in which the Certificate was issued, partial quotation of the Certificate and of the associated OIML Test Report(s) is not permitted, although either may be reproduced in full.
Issuing Authority
NMi Certin B.V., OIML Issuing Authority NL1 4 August 2025
Certification Board
This document is issued under the provision that no liability is accepted and that the applicant shall indemnify third-party liability.
OIML Certificate
OIML Member State The Netherlands
Number R129/2020-A-NL1-24.03 revision 1
Project number 3984005
Page 2 of 3
The conformity was established by the results of tests and examinations provided in the associated reports:
No. NMi-3519261-02 dated 09 December 2022 that includes 13 pages;
No. NMi-3519261-01 dated 09 December 2022 that includes 54 pages;
No. NMi-3519261-03 dated 09 December 2022 that includes 41 pages;
No. NMi-3622931-01 dated 19 January 2023 that includes 11 pages;
No. NMi-3622931-02 dated 19 January 2023 that includes 11 pages;
No. NMi-3757198-01 dated 19 April 2024 that includes 11 pages;
No. NMi-3984005-01 dated 4 August 2025 that includes 12 pages.
Characteristics of the multi-dimensional measuring instrument
Characteristics valid for all versions:
| Principle of operation | reflection of light | |
| Measuring range | single interval | |
| Electromagnetic environment class | E2 | |
| Mechanical environment class | M1 | |
| Climatic environment | temperature range | -10℃/+55℃ |
| humidity | non-condensing | |
| intended location | closed | |
| Power supply voltage | 24V DC | |
| Method of operation | automatic | |
| Software identification | Version number 2.x.y(x,y=0...999,and represent the non-legally relevant part of the software)Checksums:7378D9AF78B58803FCBF08D08296920Eor6E5DECC3E6BEA7AD90809DA8A0284B14or979F8E3290B03B73BE2166106E967BD8 | |
The software version is displayed continuously in the bottom left corner of the measurement screen. The checksum can be seen on the digital nameplate, which can be displayed by pressing the F6-key of a connected keyboard.
Characteristics valid for 1-sensor version (L135):
| Maximum dimension | Length | Width | Height |
| max≤1500mm | max≤1200mm | max≤900mm | |
| Minimum dimension | min≥100mm | min≥100mm | min≥50mm |
| Scale interval d | d≥10mm | d≥10mm | d≥5mm |
| Limitations of use | For dimensioning of singulated objects. Only rectangular objects and pillow shaped objects can be measured. Transparent packaging is not included in the measurement. | ||
OIML Certificate
OIML Member State The Netherlands
Number R129/2020-A-NL1-24.03 revision 1
Project number 3984005
Page 3 of 3
Characteristics valid for 2-sensor version (L235), 3-sensor version (L335) and 6-sensor version (L635):
| Maximum dimension | Length | Width | Height |
| max≤2600mm(L235-L335)max≤6500mm(L635) | max≤2600mm | max≤2600mm | |
| Minimum dimension | min≥200mm | min≥200mm | min≥100mm |
| Scale interval d | d≥20mm | d≥20mm | d≥10mm |
| Limitations of use | For dimensioning of rectangular shaped objects,and static palletized irregular shaped freight.Transparent packaging is not included in the measurement. | ||
| Minimum spacing between adjacent objects | spacing≥100mm | ||
Revision History
| Revision | Date | Change(s) |
| 0 | 2024-04-19 | Initial issue |
| 1 | 2025-08-04 | Addition of type L335, update for limitation of use for L135, addition of new checksum |